MARINE COMPRESSED GAS OXYGEN REGULATOR
OPERATING INSTRUCTIONS AND SAFETY GUIDE
BEFORE OPERATING YOUR OXYGEN REGULATOR,
PLEASE READ THESE INSTRUCTIONS
Nickel Plated All Brass Oxygen Regulator has been designed to provide a
constant flow of oxygen from the cylinder, directly to the oxygen diffuser.
To increase the oxygen flow, turn the selector knob from "0" to a
desired setting. Each oxygen regulator is equipped with an internal
pressure relief valve that will prevent over-pressurization of the
regulator. The KeepAlive
Oxygen Regulator is specifically designed for industrial
oxygen service only. Use of this regulator for gases other than compressed
industrial oxygen up to 2500 PSIG, is
prohibited, and any user must assume all liabilities and consequences.
NOT FOR MEDICAL USE!
stand in front of a cylinder outlet or regulator when operating the
cylinder valve. Remove the two protective covers from the 540 Valve Nipple and the Hose Barb before attempting to connect to
a cylinder. DO NOT REMOVE THE 5/8" DIAMETER
DUST COVER FROM THE SIDE OF THE REGULATOR NEXT TO THE HOSE BARB. IT
IS THERE TO HELP PREVENT CONTAMINATION. REFER TO THE
SAFETY TIPS AND WARNINGS BEFORE PROCEEDING FURTHER. Be sure to
properly inspect both the cylinder and regulator for any signs of grease and
oil. If grease or oil is suspected or found, do not use this device
1. CONNECTING THE CGA 540 NUT AND NIPPLE INLET
Check to be sure that the valve on the cylinder is off.
2. In a clockwise direction, thread the regulator inlet nut onto the cylinder
3. Tighten the inlet nut on the regulator by hand to the cylinder.
4. If oxygen is escaping at the regulator inlet after completing STEP
2, proceed to STEP 3 and then re-tighten. Many times the regulator has not
been tightened sufficiently by hand.
2. OPENING THE CYLINDER VALVE
Before turning on the oxygen cylinder valve, check to be sure that the
regulator is in the "0" position.
2. Stand behind the cylinder so that the cylinder is between you and the regulator.
Remember: Never stand in front of a cylinder outlet or regulator when
opening the cylinder valve.
3. Begin turning the cylinder valve counter-clockwise VERY
to open the valve.
4. If you suspect a leak, turn the cylinder valve off and relieve the
pressure by turning the flow selector knob clockwise and wait for the
oxygen flow to stop. Then, turn the regulator off by turning the selector
knob to the "0" position. Remove the regulator from the cylinder.
Call your KeepAlive Dealer.
3. CLOSING THE CYLINDER VALVE
With the regulator still ON, turn the oxygen cylinder valve in a clockwise
direction to OFF.
2. Allow the regulator to bleed off pressure by observing the pressure
3. When the pressure gauge reaches zero, the regulator may be removed from
Your KeepAlive regulator will last many seasons
of fishing if maintained properly. Always keeping your equipment in the KeepAlive STORAGE BAG even during use, will reduce damaging
moisture and spray.
2. Wipe down with a clean, soft cloth. If contaminated, the regulator
should be taken out of service immediately. At a minimum this oxygen
regulator should be inspected and tested to your state's regulations and
guidelines, and more often if required to ensure safety.
Operating Pressure: 500 to
Outlet Pressure: 50 PSI
LPM Settings: OFF, 1/32, 1/16,
⅛, 1/4, ½, 3/4, 1, 1 1/2, 2, and 4 liters per minute.
Configuration: CGA 540 Nut and Nipple
Outlet Configuration: Barbed Outlet for direct attachment of
SAFETY TIPS AND WARNINGS
1. Never use oil or grease
with this oxygen regulator.
2. Never use oxygen around or near an open flame.
3. Never smoke in an area where oxygen is in use.
4. Never use oxygen near boat bilges or where gasoline fumes may be
5. Never use industrial oxygen from a cylinder without reducing the
pressure through a regulator intended for that specific gas.
6. Never force connections
that do not fit properly.
7. Never permit gases to suddenly enter a regulator.
8. Refill cylinders slowly to prevent excessive heat build-up and
possible damage to cylinders.
9. Keep out of reach of children.
10. Always be sure that all fittings and threads are matched and properly
for the gas intended.
11. Never use oxygen as a pressure source to clear an obstructed line or to
operate pneumatic tools.
12. Always keep the oxygen cylinder secured.
Do not use organic-based thread
sealant on any part of this regulator. This oxygen regulator is equipped
with an internal relief valve designed to relieve excess pressure should
the regulator malfunction. This relief valve is designed to operate only as
a means of a warning signal. Should a malfunction occur, turn off the
cylinder valve immediately and disconnect the regulator. Do not attempt to
operate the oxygen regulator, unless you are properly trained.
CAUTION: Oxygen is a
non-flammable gas, however, the presence of oxygen
will drastically increase the rate of heat and combustion. Inspect for
traces of oil, grease or any other type of contamination, or connection
damage before operating. Failure to comply with these safety precautions
can result in personal injury or property damage. Do not proceed to use
until all equipment and components are correct for safe oxygen use.
AND REPAIR SERVICE
warrants that the
manufactured components of the product furnished hereunder shall be free
from defects in material and workmanship for a period of six (6) months
from the date of purchase. This warranty does not cover failure resulting
from immersion, contamination, accidental damage, misuse or operation not
in accordance with the instructions provided. To keep this warranty in
effect, all repairs must be performed by KeepAlive. This warranty is null and void if
unauthorized repairs are attempted or performed. After receipt of product, KeepAlive will evaluate and determine whether or
not the repair is covered by warranty. For repair service of any kind, you
must first call for a return materials authorization (RMA). This RMA # must
appear on the outside of the box. Any shipment received without an RMA on
the outside will be refused. You should enclose a description. of the problem. Repairs are subject to a flat labor rate
per regulator. Returns are subject to a 20% restocking fee. Returns are not
accepted after 30 days from date of purchase or if product has been used.
KeepAlive, Inc.’s obligations specifically
exclude any liability whatsoever for claims by the purchaser or user, or
any other persons or parties:
respect of merchantability or fitness for a particular purpose.
any special, indirect, incidental or consequential damages resulting
from the use, or as a result of a malfunction of the equipment.
personal injury or any medical or disability claims or for
compensation arising therefrom.
warranty and the conditions, limitations and exclusions is accepted by the
purchaser as the only authorized and applicable warranty and that there are
no other warranties or conditions, oral or written, expressed or implied.
of the harsh unforeseen conditions that the KeepAlive Oxygen Regulator
may be subjected to, the KA902-O2 regulator is
also covered by a limited-lifetime warranty. If a problem is found at any
time and caused by any reason including, but not limited to, accidental
damage and contamination, return the regulator to KeepAlive
and receive a new replacement KeepAlive
Oxygen Regulator for $75.00 plus shipping. To qualify, all regulator
parts must be included with the regulator and the the
serial number must be legible. This warranty is non-transferable and is
assigned to original purchaser only.
must first call KeepAlive at
1-727-841-0407 and give the customer service representative a valid credit
card number and obtain a Replacement Regulator Authorization Number (RRA).
This RRA number must appear on the outside
of the box containing the returned regulator. Any shipments received
without an RRA number will be refused. A new replacement KeepAlive Oxygen Regulator
will be shipped out the next business day.
UNDER NO CIRCUMSTANCES SHOULD
ANY REPAIRS, OR REPLACEMENT OF ANY PARTS BE
PERFORMED BY ANYONE EXCEPT KeepAlive.